Introduction to several factors affecting the yield of the grinding mill machine

Mill production is a great concern to the enterprise, because the production directly affects the production efficiency of the enterprise, the relationship between whether the profitability of the major events, but also the fundamental of all the issues, the operation of the enterprise is to make profits for more people to create benefits, if the production can not keep up with the enterprise will be faced with a great deal of economic problems, then the milling equipment production are affected by what factors?

In fact, the reasonableness of the supporting equipment, material inlet particle size, raw material moisture content, hardness, analyzer, wind volume and pressure and pipeline are all its influence, which aspects of the problem will affect its output, so the mill regular operation, reasonably equipped with the production line is a problem that needs to be attached great importance.

The choice of supporting machines can protect the whole set of grinding production line in the production and processing in an orderly manner, such as bucket elevator feeding elevation, electromagnetic vibrating feeder feeding uniformity, fan blowing feeding and dust removal device cooling and dust removal, etc., any one of the links have a problem, the whole set of production line will be shut down to deal with the problem, affecting the efficiency of the output, to get rid of the various aspects of the failure of the supporting equipment constraints, you need to make full preparations before the production, to ensure the rational operation of grinding production line. Ensure the rationality of the milling production line. Especially the fan air volume and wind pressure, mill work is to rely on its fan to support the strong wind, to protect the material in the whole set of devices in the flow of transmission, the wind is too large or too small are not conducive to the normal production of output.

After the selection of equipment, the humidity and hardness of the material should be rate has been considered, grinding materials according to its hardness and reasonable choice of grinding equipment, as a grinding device mill accessories in the continuous operation at the same time will inevitably have wear and tear, the material is too hard will accelerate the wear and tear of the accessories to reduce its service life, replacement of the accessories will not only delay the production schedule but also increase its production costs, the general hardness of the material Mohs hardness requirements in the following 9.3 levels; the material humidity is also the same, the same material humidity is also the same, the same material humidity is also the same. Material humidity is also the same, the same material with different moisture content, crushing and grinding, yield differences, the higher the moisture content, the greater the difficulty of grinding, grinding rollers, grinding rings and other accessories in the grinding process will be tangled roller phenomenon, to make such an analogy will not be difficult to understand, after the rain on the road vehicle tires will always be stained with a lot of dirt is the same reason, so humidity of the material in the grinding of larger materials before the drying must be dealt with! The more dry the material is, the easier it is to be rolled into powder during the grinding process, and the general humidity of ordinary Raymond mill should be controlled by less than 6%.

Material hardness is appropriate, humidity is also controlled in the specified range, we also need to consider the size of the raw material before grinding, feed size is too large or too small will affect its output, raw material size is too large, easy to clog in the feed port, waste of man-hours, into the grinding chamber of the material to the grinding rollers, grinding ring before grinding increases the difficulty; perhaps at this point will want to think about whether the material is the smaller the better, in fact, it's not, the material is too small grinding chamber under the action of the spade knife is not easy to form a material bedding layer. In fact, it is not, the material is too small in the grinding chamber in the shovel knife role is not easy to form a material mat, less material for grinding, the output is naturally low, the grinding roller, grinding ring direct contact will also produce noise, vibration, etc., the equipment will have a negative impact.

In addition to the above, the structure of the mill itself also has a certain impact on its output, such as the length and structure of the pipe, the arc duct structure is suitable for the group, the structure of the loss of air volume is small, the material in its mobility is strong, the natural yield is high, otherwise it is not, the length of the pipe is naturally the shorter the transmission process is also the smoother.

High yield, good efficiency, long service life is what every user wants, do these is not difficult, regular inspection and maintenance of equipment and maintenance, operation in strict accordance with the operating procedures, yield, life will naturally be guaranteed, in short, but also need the joint efforts of manufacturers and users.

The company has a wealth of experience to provide customers with a full set of mining equipment services, enterprises are with excellent professional skills and positive spirit of innovation to create a world-class crushing equipment, wear-resistant materials and struggle. Welcome to consult customer service to buy, free consultation.